Tabor/Obsługa/Obsługa i sterowanie EP09/en: Revision history

From TTSK

Diff selection: Mark the radio buttons of the revisions to compare and hit enter or the button at the bottom.
Legend: (cur) = difference with latest revision, (prev) = difference with preceding revision, m = minor edit.

(newest | oldest) View ( | older 50) (20 | 50 | 100 | 250 | 500)

12 August 2025

  • curprev 08:5708:57, 12 August 2025 Maszn talk contribs 20,018 bytes −102 Created page with "Remember that each time the direction selector is moved to or through the "0" position, the auxiliary relay must be powered by pressing the traction motor overload relay release button (<code>N</code> key)."
  • curprev 08:5708:57, 12 August 2025 Maszn talk contribs 20,120 bytes −79 Created page with "The first thing you need to do to prepare for driving is to set the direction selector in the desired direction (<code>Page Up</code> or <code>Page Down</code> keys). When the direction is set, the indicator lights on the left side of the panel will light up."
  • curprev 08:4808:48, 12 August 2025 Maszn talk contribs 20,199 bytes −66 Created page with "When editing the consist, if you uncheck the "Cold start" option, the locomotive will be in an almost ready state when the simulation starts."
  • curprev 08:4508:45, 12 August 2025 Maszn talk contribs 20,265 bytes −25 Created page with "=== Quick start ==="
  • curprev 08:4508:45, 12 August 2025 Maszn talk contribs 20,290 bytes −63 Created page with "After completing all of the above steps, the locomotive is ready to run."
  • curprev 08:4308:43, 12 August 2025 Maszn talk contribs 20,353 bytes −68 Created page with "The last step is to unlock the traction motor overload relay (<code>N</code> key)."
  • curprev 08:4108:41, 12 August 2025 Maszn talk contribs 20,421 bytes −74 Created page with "When the brake cylinder pressure gauge shows values close to zero, set the combined brake valve to the drive position (<code>Num4</code>)."
  • curprev 08:3908:39, 12 August 2025 Maszn talk contribs 20,495 bytes −80 Created page with "The next step is to turn on the main switch (<code>M</code> key) and engage it (<code>Shift + M</code> keys). A closed main switch will be indicated by a light on the dashboard."
  • curprev 08:3808:38, 12 August 2025 Maszn talk contribs 20,575 bytes −55 Created page with "These actions should be monitored on the pressure gauges located on the right side of the panel."
  • curprev 08:3608:36, 12 August 2025 Maszn talk contribs 20,630 bytes −94 Created page with "To do this, set the combined brake valve to the release position (<code>Num.</code> key), hold down the brake release button (<code>Num6</code> key), and wait until the pressure in the break pipe reaches 0,5 MPa and the brake cylinders are emptied."
  • curprev 08:3008:30, 12 August 2025 Maszn talk contribs 20,724 bytes −98 Created page with "The next sterp is to turn on the compressor (<code>C</code> key) and wait for the main reservoir to fill up. Then the pressure gauge of the main reservoir exceeds 5 bar, you can proceed to fill the break pipe with the air."
  • curprev 08:3008:30, 12 August 2025 Maszn talk contribs 20,822 bytes −92 Created page with "Next, turn on the converters (<code>X</code> key) and wait for the battery charging current to sabilize. This process should be monitored on the low-voltage ammeter."
  • curprev 08:2008:20, 12 August 2025 Maszn talk contribs 20,914 bytes −73 Created page with "After raising the pantographs, wait a few seconds until they touch the overhead wires. When this happens, you will see the voltage on the high-voltage voltometer raise from zero to approximately 3kV."
  • curprev 08:1708:17, 12 August 2025 Maszn talk contribs 20,987 bytes −278 Created page with "Then you can proceed to raise the pantographs (<code>O</code> and <code>P</code> keys). Which pantograph should be raised depends on the direction of travel. Under normal conditions, the rear pantograph is used, while the front one is reserved for emergency situations."
  • curprev 08:1408:14, 12 August 2025 Maszn talk contribs 21,265 bytes −102 Created page with "Remember that each time the direction selector is moved to or through the "0" position, the auxiliary relay must be powered by pressing the traction motor overload relay release button (<code>N</code> key)."
  • curprev 08:1108:11, 12 August 2025 Maszn talk contribs 21,367 bytes +131 Created page with "Na nastawniku kierunkowym należy ustawić żądany kierunek jazdy (klawisze <code>Page Up</code> lub <code>Page Down</code>). Po ustawieniu kierunku zapalą się lampki kontrolne po lewej stronie pulpitu. Then, you should set the direction on (<code>Page Up</code> or <code>Page Down</code> keys). When the direction is set, the indicator lights on the left side of the panel will light up."
  • curprev 08:0708:07, 12 August 2025 FuzzyBot talk contribs 21,236 bytes +619 Updating to match new version of source page

6 August 2025

(newest | oldest) View ( | older 50) (20 | 50 | 100 | 250 | 500)
Retrieved from "https://wiki.ttsk.ngo/index.php?title=Tabor/Obsługa/Obsługa_i_sterowanie_EP09/en"